Railway Preservation News
https://www.rypn.org/forums/

Hicks Seat Castings
https://www.rypn.org/forums/viewtopic.php?f=1&t=40759
Page 1 of 1

Author:  wcb07 [ Fri Jun 02, 2017 9:07 am ]
Post subject:  Hicks Seat Castings

The Mid-Continent Railway Museum Restoration Department has recently completed reproducing the cast seat parts for Lake Superior & Ishpeming coach #64 that is undergoing restoration.

http://www.midcontinent.org/equipment-r ... peming-64/

The seat castings had to be made as the seat design and castings are unique to the car builder (Hicks Locomotive & Car Works) and the museum could not simply tap into the museum’s seat inventory to accurately restore the car. 12 of the 26 Hicks seats were missing from the car when MCRM acquired the car in 1985. In a cooperative effort Mid-Continent arranged to have 12 sets of castings made for the missing seats in Yosemite Valley #330, another Hicks produced car that is undergoing restoration at the Niles Canyon Railway.

Given that Hicks Locomotive & Car Works went out of business (bankrupt) in late 1910, these are likely the first Hicks seats that have been made in the last 107 years.

Bill Buhrmaster
MCRM Restoration Dept.


Attachments:
IMG_6123 (1).jpg
IMG_6123 (1).jpg [ 45.59 KiB | Viewed 6384 times ]
IMG_6119.jpg
IMG_6119.jpg [ 50.85 KiB | Viewed 6384 times ]

Author:  Loco112 [ Fri Jun 02, 2017 6:19 pm ]
Post subject:  Re: Hicks Seat Castings

More, photos Please.

Its difficult to see a part when in a box of so many other parts.

I'm anxious to see how these look when going together and how they look all assembled and complete.

Author:  wcb07 [ Sat Jun 03, 2017 8:43 am ]
Post subject:  Re: Hicks Seat Castings

There are (6) different cast parts associated with each seat and a total of (10) cast parts for each seat. The photos below show each of the parts along with sub-assemblies and finally a vintage photo of a completed and assembled seat.

We have not assembled any of the new castings or seats as the car is presently undergoing an extension restoration and we won't be ready for the seats for several years.

I hope this helps.

Bill Buhrmaster
MCRM
Restoration Dept.


Attachments:
File comment: Inner (wall side) foot support bracket
1 inner.jpg
1 inner.jpg [ 206.73 KiB | Viewed 6089 times ]
File comment: Aisle end foot support
2 aisle foot.jpg
2 aisle foot.jpg [ 210.87 KiB | Viewed 6089 times ]
File comment: Seat base sub-assembly
3Base.jpg
3Base.jpg [ 111.18 KiB | Viewed 6089 times ]
File comment: Seat back mechanism
4 mechanism.jpg
4 mechanism.jpg [ 76.18 KiB | Viewed 6089 times ]
File comment: Hicks Seat - complete in LS&I 63
5 63 assy.jpg
5 63 assy.jpg [ 132.91 KiB | Viewed 6089 times ]
File comment: Restoration of LS&I #64
lsi-64.jpg
lsi-64.jpg [ 300.9 KiB | Viewed 6089 times ]

Author:  Dennis Storzek [ Sat Jun 03, 2017 1:45 pm ]
Post subject:  Re: Hicks Seat Castings

Bill,

Can you share with us which foundry did the work? The Amish at Cattail Foundry, or someone else? It looks like you used existing parts as patterns, which I understand is Cattail's forte.

Author:  wcb07 [ Sat Jun 03, 2017 1:57 pm ]
Post subject:  Re: Hicks Seat Castings

The seat parts were cast at the Tomahawk Foundry.

http://www.tomahawkfoundry.com/home

Bill Buhrmaster

Author:  John Risley [ Sat Jun 03, 2017 5:07 pm ]
Post subject:  Re: Hicks Seat Castings

I have heard very good reports so far from this foundry. They do use or can use original castings for patterns. I was turned on to this foundry from a shop that restores antique wood and coal stoves. When he gets something rare that he stands to profit on he and others in the stove restoration business have work done here. Brake shoes for the Polson #2 were done here as well.

Have no connection to this foundry but have heard very good reports of there work and willingness to do small or one of a kind pours. At this time I have not personally used them but I do have a project in mind for them. Regards, John.

Author:  David Johnston [ Sun Jun 04, 2017 5:29 pm ]
Post subject:  Re: Hicks Seat Castings

The smaller thin section castings may have been malleable iron originally to reduce breakage. An appropriate replacement today would be ductile iron. The selection of a foundry would have to be made to find someone that can cast the grade of iron needed for this application.

Author:  John Risley [ Sun Jun 04, 2017 11:07 pm ]
Post subject:  Re: Hicks Seat Castings

Quote from the foundrys web site:

http://www.tomahawkfoundry.com/home





"Molding is done in furan bonded sand and in green sand using 16 x 20 B&P automatic molding, Squeezer and Rotolift molding machines. We pour gray and ductile iron using induction furnaces".

Regards, John.

Page 1 of 1 All times are UTC - 5 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/