| Railway Preservation News https://www.rypn.org/forums/ |
|
| Fusible Plugs https://www.rypn.org/forums/viewtopic.php?f=1&t=8467 |
Page 1 of 1 |
| Author: | PKurilecz [ Thu Feb 12, 2004 4:19 pm ] |
| Post subject: | Fusible Plugs |
Hello All: I need a source for fusible plugs. Any leads? Respond off list if you prefer. Cheers; PKurilecz pkurilecz@yahoo.com |
|
| Author: | Adam Mizer [ Thu Feb 12, 2004 6:41 pm ] |
| Post subject: | Re: Fusible Plugs |
Eugene Ernst company has fusible plugs. They also handle sight glass supplies, water reading devices etc. 732 938-5641 |
|
| Author: | Jim Adams [ Fri Feb 13, 2004 1:05 am ] |
| Post subject: | Re: Fusible Plugs |
> Hello All: > I need a source for fusible plugs. Any > leads? > Respond off list if you prefer. > Cheers; > PKurilecz Have you tried McMaster-Carr Supply Co. 600 County Line Road Elmhurst. IL 630-834-9600 They have just about anything you need. You didn't mention size. What are these for? What pressure will they be under? If it is an odd size or you need oversize threads you can make your own. They are easy to make. Jim rrfanjim@charter.net |
|
| Author: | J.David [ Fri Feb 13, 2004 5:31 am ] |
| Post subject: | Re: Fusible Plugs |
> You didn't mention size. What are these for? > What pressure will they be under? > If it is an odd size or you need oversize > threads > you can make your own. They are easy to > make. Greetings: In my opinion, making your own fusible plug isn't a good idea. You can not make an ASME fusible plug. They can only be made by an ASME shop. If you have an odd size opening, make a bushing to take a standard NPT thread or properly repair the sheet to take a standard NPT thread. J. David jdconrad@snet.net |
|
| Author: | R. L. Musser [ Fri Feb 13, 2004 11:18 am ] |
| Post subject: | Re: Fusible Plugs |
> Hello All: > I need a source for fusible plugs. Any > leads? > Respond off list if you prefer. > Cheers; > PKurilecz Ernst & Whitney Pressure Products, Inc. Waynesboro, Pa. 1-717-762-8723 rick@strasburgrailroad.com |
|
| Author: | John Deck [ Fri Feb 13, 2004 11:42 am ] |
| Post subject: | Re: Fusible Plugs |
There is an excellent article in the September 2003 edition of Steam Traction about fusible plugs. I would recommend this as must read for anyone who is operating a steam boiler with plugs in it. I am not sure if you can buy single copy issues but there web address is www.steamtraction.com. Bruce Babcock who is on the Ohio Historical Boilers Licensing Board wrote the article. He goes into great detail about fusible plugs and after you read this article you will understand the need to change them on a regular basis. They are cheap to replace when you consider the cost if one fails to do its job and there is a failure. johndeck@cox.net |
|
| Author: | Jim Adams [ Fri Feb 13, 2004 12:35 pm ] |
| Post subject: | Re: Fusible Plugs |
> Greetings: > In my opinion, making your own fusible plug > isn't a good idea. You can not make an ASME > fusible plug. They can only be made by an > ASME shop. If you have an odd size opening, > make a bushing to take a standard NPT thread > or properly repair the sheet to take a > standard NPT thread. > J. David Mr. David; In our present litigious society, you are right. It is probally not smart to make soft plugs. However, the fact remains they are easy to make and I know the ones I have made function properly because one operator blew two of them within about an hour. He hadn't cleaned his gauge cocks in months and the top cock was plugged with scale thus causing a false water level reading**. He called me and complained about "Something was wrong with the soft plugs, they wouldn't hold." This was after the plug had worked fine since the start of the season. When we found the plugged gauge cock I told him the soft plugs were doing exactly what they were supposed to do and that he was d****d lucky they had. Making your own plugs allows you to fit a hole that is a few/1000ths oversize due to over energetic thread chasing. Something that bushing the hole won't accomplish. And while the fact of the soft plug is that the melting point of the Tin mixture determines when the plug lets go,and there is nothing the maker does when he fills the plug that affects that melting point, and that having an ASTME stamp doesn't change the melting point of the fusible mixture, these facts would probally be a poor defense in our present courts. Jim ** I believe the Gettysburg explosion was attributed to this same condition. rrfanjim@charter.net |
|
| Author: | John Hewlett [ Thu Feb 26, 2004 11:10 am ] |
| Post subject: | Re: Fusible Plugs |
> Hello All: > I need a source for fusible plugs. Any > leads? > Respond off list if you prefer. > Cheers; > PKurilecz Steam Traction lists two sources: D & H Spring, Ask for Corky, 1-800-382-3917 Stellar Industrial Technologies 1-740-654-7052 jhewlett@co.genesee.mi.us |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|