It is currently Fri Oct 02, 2026 9:14 am

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 10 posts ] 
Author Message
 Post subject: GG-1 in Harrisburg
PostPosted: Thu May 26, 2005 4:17 pm 

Joined: Sun Aug 22, 2004 8:34 pm
Posts: 670
Location: Union, IL
When I passed through Harrisburg on the "Pennsylvanian" Monday, I noticed that someone had been drawing on GG-1 #4859 in chalk. The entire side of the locomotive was divided into squares (more or less), I would say about 3'-4' square, and each was individually numbered. Does anyone have any idea why, or what's going on?

_________________
Frank Hicks
Preserved North American Electric Railway Equipment News
Hicks Car Works


Offline
 Profile  
 
 Post subject: Re: GG-1 in Harrisburg
PostPosted: Fri May 27, 2005 12:05 pm 

Joined: Sat Nov 20, 2004 3:18 pm
Posts: 150
maybe the locals are preparing for ultrasound testing......


Offline
 Profile  
 
 Post subject: Re: GG-1 in Harrisburg
PostPosted: Fri May 27, 2005 6:51 pm 

Joined: Sun Oct 24, 2004 10:29 am
Posts: 401
Location: Scranton, PA
Thats what came to my mind.. but.. why would you ultrasound a GG-1?!? Sheetmetal can be replaced alot more easily than boiler courses!


Offline
 Profile  
 
 Post subject: Re: GG-1 in Harrisburg
PostPosted: Fri May 27, 2005 7:02 pm 

Joined: Sun Aug 22, 2004 1:51 pm
Posts: 12170
Location: Somewhere east of Prescott, AZ along the old Santa Fe "Prescott & Eastern"
I'm due through town shortly.If there's not a better answer forthcoming soon, I may be tempted to write "flank steak", "rump roast", "tenderloin", etc. in the grids just to get some attention on the gal..........


Offline
 Profile  
 
 Post subject: Re: GG-1 in Harrisburg
PostPosted: Fri May 27, 2005 8:40 pm 

Joined: Sun Aug 22, 2004 11:26 am
Posts: 4777
Location: Maine
Ultrasound? I didn't even know it was pregnant!

_________________
"It's only impossible until it's done." -Nelson Mandela


Offline
 Profile  
 
 Post subject: Re: GG-1 in Harrisburg
PostPosted: Sat May 28, 2005 6:46 am 

Joined: Sun Aug 22, 2004 5:15 am
Posts: 718
Location: Illinois
Clearly this must be the pilot project to develop yet more new regulations for preservation, covering paint removal, etc for all equipment, static and operating, on track and off. Thus the very real perceived need for ultrasound mapping, documentation, and experimental and comparative methods in adjoining grid sections.Either that or Ralston Purina from Checkerboard Square is sponsoring a re-paint.Bob Kutella


Offline
 Profile  
 
 Post subject: Re: GG-1 in Harrisburg
PostPosted: Sun May 29, 2005 3:43 pm 

Joined: Mon Aug 23, 2004 9:01 am
Posts: 13
Location: Harrisburg, PA
Pregnant? Wouldn't that be great! A new baby GG-1 (maybe she caught wind of the Acela problems and wanted to do her part)! Given her size though, I am guessing it would be a 2 year gestation?Scott


Offline
 Profile  
 
 Post subject: Re: GG-1 in Harrisburg: Goes NASCAR
PostPosted: Tue May 31, 2005 11:48 am 

Joined: Sun Aug 22, 2004 11:54 am
Posts: 746
Location: Michigan
Nah, the whole checkerboard thing is due to the new NASCAR sponsorship of rail preservation--- think checkered flag.TJG


Offline
 Profile  
 
 Post subject: Re: GG-1 in Harrisburg
PostPosted: Tue May 31, 2005 1:47 pm 

Joined: Sun Aug 22, 2004 9:11 pm
Posts: 81
Location: Where ever I am at the time
PRR1223 wrote:
Pregnant? Wouldn't that be great! A new baby GG-1 (maybe she caught wind of the Acela problems and wanted to do her part)! Given her size though, I am guessing it would be a 2 year gestation?Scott
You don't suppose a GG-1 got kn*cked up by the Acela do you? What an ugly baby that would be!


Offline
 Profile  
 
 Post subject: Re: GG-1 in Harrisburg: Goes NASCAR
PostPosted: Tue May 31, 2005 2:55 pm 

According to reports on the PRR FAX list, this locomotive is being investigated for traces of PCB's in its surface. According to other reports on the same list PRR 4800 was sandblasted and repainted because PCB traces were found in its paint. I would appreciate any firm information on what was found and what actions were taken. Below is an EPA press release on the actions taken at the Railroad Museum of Pennsylvania.Tom Cornilliehttp://yosemite.epa.gov/r3/press.nsf/0/6f0ebb12d7403e5b85256ebc006be63c?OpenDocumentFor Immediate Release: June 23, 2004 Pa. Historical and Museum Commission Settle PCB Violations - Railroad Museum to Complete EPA-Approved Cleanup Bonnie Smith, 215-814-5543PHILADELPHIA – The U.S. Environmental Protection Agency has announced that the state commission that runs the Railroad Museum of Pennsylvania in Strasburg, Pa., has settled a case involving leaks of polychlorinated biphenyl (PCB) fluid from a historic locomotive at the museum.In a consent agreement with EPA, the Pennsylvania Historical and Museum Commission has agreed to pay a $28,836 penalty to settle alleged violations of federal regulations on the storage and disposal of PCBs and PCB-containing equipment. The commission has committed to cleanup and dispose of PCBs and PCB-containing equipment at the museum. PCBs, a probable human carcinogen, were once widely used as a nonflammable coolant for transformers and other electrical equipment. In 1976, Congress enacted the Toxic Substances Control Act, which strictly regulated the manufacture, use and disposal of PCBs. For information on the health effects, regulations, and cleanup of PCBs, visithttp://www.epa.gov/opptintr/pcb/.On March 14, 2002, Pennsylvania officials notified EPA about the discovery of PCB transformers on four locomotives at the museum, and a leak of PCB fluid from one such transformer. Museum officials also informed EPA of PCB-contaminated soil at the museum.In consultation with EPA, the commission developed a plan for the cleanup of the PCB leak, the soil contamination, and the disposal of PCB-containing transformers at the museum. Under this plan, which EPA approved on September 15, 2003, the commission developed specifications for PCB cleanup and transformer disposal, and has remediated the PCB-contaminated soil. Soil and transformer removal and disposal have been completed. The remaining portions of the cleanup are scheduled to be completed by September 2005.As part of the settlement of this matter, the commission has neither admitted nor denied liability for the alleged violations. EPA will continue to work with the Pennsylvania officials until the completion of the cleanup.


  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 10 posts ] 

All times are UTC - 5 hours [ DST ]


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to: